Household Major Electric Appliances Install or Replace Lower Mainland Vancouver BC


Vancouver Appliance Repair Service
Home Services About Us Contact Us Policies Customer Comments Appliances Info FAQ Safety First

Installation and Replacement For All Major Electric Appliances

INSTALL OR REPLACE ALL MAJOR HOME ELECTRIC APPLIANCES IN VANCOUVER AREA

MAYTAG Clothes Washer - Centennial Commercial Technology EcoConserve Energy Star
Model MVWC400XW4
Serial C30231158
Type: 588-10

MAYTAG Clothes Dryer - Commercial Technology
Model YMEDC200XW3
Serial CWSR-ELE-2406024-FMS0

Stainees Steel Braided Hose - Steel-Flex
- Inlet hoses, Hot (H) & Cold (C) water are they five or ten years or older should be replaced.
- Grey Inlet Hoses every 5 years.
- Black rubber inlet hoses every 5 or 10 years.
- Stainless steel braided inlet hoses every 5 or 10 years.
Never replace for White Plastic Clothes Dryer Vent.













 
Alwas check the connection Cold and Hot Water.














 
Alwas check the Washer Level.















 
Alwas check the Dryer Level.















 

 

Air Dolly - replaced Steel-Flex Hoses.

 

Some Tips:
- Washer legs adjustment GE (General Electric)
Washer legs adjustment:
Adjust the washer front legs by spinning them usually counter clockwise will raise the legs against the floor to raise the washer front slightly. The washer should be level side to side and just barely higher on the front than in the back (level stick "air gap" in the middle just touching in the level). Lock leveling leg in position using leg lock nuts.

This Washing Machine has "self-adjusting" rear legs. These legs are set by tilting the entire machine forward onto its front legs with the rear legs 3 inches 7.62 centimeter off the floor and then setting the machine back down. The legs should set back on the floor (adjust automatically). If they do not, you may need to tilt the machine forward again and rap on the rear legs (you can lubricate rear mechanism) with the a rubber hammer to loosen.

- Washer legs adjustment MAYTAG
Washer legs adjustment:
Adjust the washer front legs by spinning them usually counter clockwise will raise the legs against the floor to raise the washer front slightly. The washer should be level side to side and just barely higher on the front than in the back (level stick "air gap" in the middle just touching in the level). Lock leveling leg in position using leg lock nuts.

Some a Top-Load Washers have "self-adjusting" rear legs. These legs are set by tilting the entire machine forward onto its front legs with the rear legs 3 inches 7.62 centimeter off the floor and then setting the machine back down. The legs should set back on the floor (adjust automatically). If they do not, you may need to tilt the machine forward again and rap on the rear legs (you can lubricate rear mechanism) with the a rubber hammer to loosen.

- Cleaning - Dryer Vent cleaning
- Built-in dishwasher installation instructions
- How to install a garburator
- Installation - Range Hoods

 

WARNING!
Always disconnect electrical power before beginning any service repair procedures.

Latest News


Google Reviews for Andy's Appliance & Refrigeration in Vancouver, BC 2017-04-02  Welkom to Andy's Appl...
» Read more    

HomeStars Reviews for Andy's Appliance & Refrigeration in Vancouver, BC 2017-03-17 Welkom to Andy's Appliance ...
» Read more    

Yelp Reviews our Valued Clients in Vancouver, BC 2017-02-27 Welkom to Andy's Appliance ...
» Read more    

The Best of Home Appliance Repair Company in Vancouver, BC 2017-02-24  Thank You for opportu...
» Read more    

Blomberg Appliance Repairs 2015-06-09  BLOMBERG EUROPEAN HOU...
» Read more    

» Browse archive